Investigation of the relationship between intergranular corrosion and retrogression and reaging in the AA6063

AA6063 was heat treated with different retrogression temperatures and durations, and the effect of heat treatment conditions on the microstructure, hardness, electrical conductivity, intergranular corrosion (IGC) and electrochemical corrosion behaviours of the AA6063 was determined compared with the T6 condition. The IGC test was applied according to the BS EN ISO 11846: 2008 standard. Moreover, potentiodynamic polarization tests were applied to determine the electrochemical corrosion behaviour of the heat‐treated samples. Electrochemical corrosion tests were carried out by using a Ivium Compactstat potentiostat in 3.5 wt.%. NaCl solution at 24°C with a scanning rate of 0.5 mV/s. The corrosion test cell consisted of the reference electrode (Ag/AgCl), working electrode (test sample) and a reference electrode (platinum). The effect of IGC on the microstructure of AA6063 and corrosion depth values was investigated by using a stereo optical microscope and a light metal microscope, respectively. Corrosion depth examinations were performed on microstructures taken from the cross‐sections of the samples. The chemistry of the precipitates formed at grain boundaries and distribution of the precipitates in the microstructure were investigated by scanning electron microscope, energy dispersive X‐ray and transmission electron microscope analyses. The results showed that retrogression and reaging heat treatment improves both the corrosion resistance and the mechanical properties of AA6063. After 50°C/15 min RRA heat treatment, the highest corrosion resistance and a higher hardness value than the T6 level were obtained.     

300M超高强钢在中性盐雾环境中的腐蚀行为及机制

摘要：为了研究300M超高强钢在中性盐雾环境中的腐蚀行为及腐蚀机制，采用失重法，宏观、微观腐蚀形貌分析，三维表面轮廓分析及电化学分析的研究方法，来表征腐蚀实验现象并进行分析。结果表明：300M超高强钢在中性盐雾环境中的腐蚀产物为FeOOH、Fe2O3、Fe(OH)3和Fe3O4；腐蚀速率随着腐蚀时间逐渐降低，腐蚀后期（72h）腐蚀速率降低50%；腐蚀初期以点蚀为主，点蚀坑通过横向扩展，逐渐发展为后期的均匀腐蚀，腐蚀表面形貌呈沟壑状；外腐蚀层对基体的保护能力很弱，Cr元素在锈层靠近基体的一侧偏聚使内腐蚀层具有一定的抗腐蚀性。     

Theoretical and experimental studies of a new aniline derivative corrosion inhibitor for mild steel in acid medium

4-Chloro-N-(pyridin-2-ylmethyl)aniline (CPYA) was synthesized by a simple and inexpensive method and tested as a corrosion inhibitor in acid medium for mild steel by using gravimetric studies and electrochemical measurements. An average maximum efficiency of 96.0% was achieved at 4.59 mmol/L. Corrosion kinetic and thermodynamic parameters were also analyzed. Surface analyses (atomic force microscopy and scanning electron microscopy) show that protection is enabled by adsorption on the metal, forming a film. Quantum chemical calculations were performed to access information regarding the molecular structure in the corrosive medium and to support interpretation of the results obtained by experimental methods.     

Corrosion behaviour and mechanism of 6082 aluminium alloy in NaCl and Na2SO4 etchants

The corrosion behaviour of 6082 aluminium alloy was studied by measuring the electrochemical impedance spectra and electrode polarization curves. After the electrochemical tests, a microstructural analysis of the samples was conducted by using optical microscopy and electron scanning microscopy techniques to determine the corrosion mechanism. The results show that the Nyquist plot of the electrochemical impedance data in the NaCl solution consists of high- and low-frequency capacitive impedance loops. When ions are added to the NaCl etchant, the Nyquist plots of the electrochemical impedance data are composed of two different curves: a high-frequency capacitive impedance loop and a low-frequency inductive impedance loop. The corrosion current density increases with increasing concentration, and as a result, the corrosion resistance of the aluminium alloy decreases. The microstructures of 6082 aluminium alloy consist of Mg₂Si secondary particles in a large α-Al matrix. Pitting corrosion initially occurs at the boundary between the matrix and secondary particles because the electrode potentials of the matrix and secondary particles are different. Then, corrosion paths develop along the network-like grain boundaries, and finally, massive network-like corrosion occurs throughout the entire alloy.     

Microstructure and corrosion behaviors of FeCrNiBSiMox stainless steel fabricated by laser melting deposition

In this paper, FeCrNiBSiMo_x (x = 1.0, 1.5, 2.0, 2.5) stainless steels were successfully prepared using a laser melting deposition technology, with the aim to investigate the effect of Mo content on microstructure and corrosion behaviors. The results showed that the as-deposited specimens were composed mostly of α-Fe and a small amount of (Cr, Mo)₇C₃, and (Cr, Mo)₇C₃ existed in the inter-dendritic (ID) region. As the Mo content increased, grain refinement could be clearly observed, and the area of the ID region increased from 27% to 54%. The low-angle boundaries accounted for 60–70% of the grain boundaries of the as-deposited specimens. Increasing the content of Mo improved the microhardness of the as-deposited specimens from 652 HV to 813 HV. The corrosion current density of the as-deposited specimens with the Mo mass fractions of 1.0%, 1.5%, 2.0%, and 2.5% were 1.37 × 10⁻⁶, 1.02 × 10⁻⁷, 6.19 × 10⁻⁷, and 3.06 × 10⁻⁷ A/cm², respectively. The as-deposited specimen with Mo content of 1.5% had lower cumulative erosion loss and erosion loss rate than other as-deposited specimens. The FeCrNiBSiMo_x (x = 1.5) specimen exhibited excellent resistance to electrochemical corrosion and cavitation erosion.     

Effects of Al content on the corrosion properties of Mg–4Y–xAl alloys

The corrosion performances of Mg–4Y–xAl (x = 1, 2, 3, and 4 wt%) alloys in the 3.5% NaCl electrolyte solution are investigated by electrochemical tests, weight loss measurement and corrosion morphology observation. The results indicate that corrosion modes for the alloys are localized corrosion and the filiform type of attack. With Al concentration increasing from 1 to 4 wt%, the corrosion rate of Mg–4Y–xAl alloys decreases firstly and then increases, and WA42 alloy shows the best corrosion resistance. The addition of Al element to Mg–4Y alloys leads to the formation of Al₂Y and Al₁₁Y₃ intermetallic compounds and reduces the proportion of Mg₂₄Y₅ phase. Corrosion resistance of the Mg–4Y–xAl alloys mainly depends on the size and distribution of the second phases. Besides, the addition of excessive Al can greatly consumes the Y element in the matrix, thus leading to a less protective film on the alloys. The effect of the relative Volta potential changes between the second phases and α-Mg on corrosion resistance of Mg–4Y–xAl alloys is insignificant. The main corrosion products of the Mg–4Y–xAl alloys are Mg(OH)₂, Mg₃(OH)₅Cl·4H₂O, Mg_0.72Al_0.28(CO₃)_0.15(OH)_1.98(H₂O)_0.48, and Mg₄Al₂(OH)₁₂CO₃·3H₂O.     

微观组织对2A14铝合金轮毂力学性能和腐蚀性能的影响

通过电子背散射衍射(EBSD)、场发射扫描电子显微镜(SEM)、透射电子显微镜(TEM)、室温拉伸、浸泡腐蚀、电化学极化等测试分析方法，研究了2A14铝合金轮毂内部不同区域上微观组织的差异及其对力学性能和腐蚀性能的影响。结果表明，2A14铝合金轮毂的芯部和1/4层的晶粒尺寸分别是113和54 μm，再结晶分数分别是16%和36%。1/4层的合金相和时效析出相的含量都大于芯部，其中两种时效析出相(θ’和Q相)的数量密度均为芯部的2倍左右。芯部具有较大的晶粒尺寸和较少的时效析出相，因此具有较低的力学性能。同时，芯部相对于1/4层具有较少的合金相和较大的晶界相间距，因而芯部的电化学腐蚀和晶间腐蚀倾向均低于1/4层。